Type in the full discussion title or a part of it.
Discussion Title Created date
I2C or TWI stuck
Hi ! I have problem with i2c communication. At begining of main() I initialize i2c and read RTC DS1337 and my program gets stuck. SCL and SDA are toggling. Datasheet says (http...
Wednesday, 9 October 2013 - 10:02
ATmega1281 - pin current question
Hi all ! I would like to drive optocoupler with GPIO pins and what concerns me is how many mA can port give me. Reading datasheet p.367 at top of the page: DC Current per I/O Pin...
Tuesday, 10 September 2013 - 11:27
[LW Mesh] Tx power
Hi ! I have questions about TX power: 1. How can I read back TX power value which I've set with PHY_SetTxPower(); ? 2. When can TX power be set? At any time or... ? Thank you...
Tuesday, 30 July 2013 - 18:21
[LW Mesh] Broadcast and unicast
Hi ! I have problem with BROADCAST transmission in LW Mesh. What I would like to do is sending BROADCAST and UNICAST(acknowledge) messages. I know that BORADCAST in NOT...
Monday, 22 July 2013 - 19:12
[LW Mesh] SPI on LW Mesh
Hi all ! I would like to get SPI to work in LW_Mesh. I'm using ATZB-A24-UFLB and used pins for that are: 38 -> USART0_RXD 39 -> USART0_TXD 40 -> USART0_EXTCLK and my CS -> chip...
Friday, 14 June 2013 - 17:40
AS 6 - view problem
Hi ! While I was writing I accidentally pressed some shortcut for this -> . I would like to get rid of these -> (so annoying) , but I don't know how( please,see picture). I had...
Monday, 10 June 2013 - 09:30
[LW Mesh] Interrupt and WDT
Hi ! I have questions about interrupts and WDT in LW Mesh. I'm using ATZB-A24-UFLB module. 1. ATZB-A24-UFLB module has interrupts IRQ_6 and IRQ_7 and I use them LOW. To enable...
Thursday, 6 June 2013 - 18:54
[LW Mesh] Frequency problem
Hi ! I'm using ATZB-A24-UFLR module with LW Mesh. My main looks like this: int main(void) { SYS_Init(); HAL_UartInit(38400); while (1) { SYS_TaskHandler();...
Monday, 27 May 2013 - 15:42
Lightweight Mesh error
Hi! I've just started to "play" with Lightweight Mesh and I have problem building template application. I use AVR Studio 5.1.208 on Windows 7 64-bit, new installation both. I...
Friday, 26 April 2013 - 11:54
UART vs. APS_DataInd()
Hi ! I use BitCloud v13 on ATZB-A24-UFL. My problem is like this: I have network with COORDINATOR(gateway to PC through UART) and few nodes ROUTERS or END DEVICES. My...
Saturday, 16 March 2013 - 19:44
[BitCloud] IRQ and wake up problem
Hi all! My problem is like this (BitCloud v.13): I have coordinator and one end device which sleeps 10 seconds and is awake for 3 seconds. Problem is that end device can't wake...
Wednesday, 21 November 2012 - 10:44
Sending messages ED to ED
Hi ! I have network(with coordinaotr, Rs nad EDs) in which EDs(are sleeping) send messages to each other. I use acknowledge transmission (BitCloud v13). What happens if one ED...
Thursday, 1 November 2012 - 14:00

Pages